Fortinet
Knowledge Base
Browse: Products
Chassis
Customer Service & Support
FortiADC, AscenLink, Coyote Point
FortiAnalyzer
FortiAP
FortiAuthenticator
FortiBalancer
FortiBridge
FortiCache
FortiCarrier
FortiClient
FortiCloud
FortiController
FortiDB
FortiDDoS
FortiDirector (XDN)
FortiDNS
FortiExplorer
FortiExtender
FortiFone
FortiGate
FortiGuard
FortiMail
FortiManager
FortiMobile
FortiRecorder
FortiSandbox
FortiScan
FortiSwitch
FortiToken
FortiVoice
FortiWeb
FortiWiFi
TalkSwitch

News
Fortinet Video Library
Short demos which illustrate some basic FortiGate configurations.

RSS Feed
KB Site Feedback
KB Site Help
KB Article Index
What's New   1 - 5 of 7    < prev | next 2 >
“Get signal strength” diagnostic returns "0,99"    Knowledge Article
The Fortigate’s FortiExtender page shows that the FortiExtender is authorized and the link is up.  However, when running the GUI diagnostic *“Get signal strength”* returns *“+CSQ: 0,99 OK”*. *
Modem Connection fails when using FortiExtender and AT&T Netgear 340U modem    Knowledge Article
*Problem:* Modem Connection fails when using FortiExtender and AT&T Netgear 340U modem *Symptom:* “get extender modem-status” returns an empty list Note:*  *Even
Technical Note: Why is the FortiExtender Link Status down?    Knowledge Article
On systems running FortiOS v5.2.1 and below, there is a field called Link Status located under System> Network > FortiExtender. This status does not indicate that the physical link
Technical Note: Forwarding logs between FortiAnalyzers    Knowledge Article
This article explains how to forward logs from one FortiAnalyzer (FAZ) to another FortiAnalyzer. The source FortiAnalyzer has to be able to reach the destination FortiAnalyzer on tcp
How to view and report upon logs after a FortiGate has been replaced (due to RMA)    Knowledge Article
This article explains how to ensure continuity in reporting on the FortiAnalyzer (FAZ) when a managed FortiGate is replaced due to RMA.  By following the
< prev | next 2 >
Most Popular   1 - 5 of 10    < prev | next 5 >
Technical Note : Loading FortiGate firmware image using TFTP    Knowledge Article
Description This article describes how to download and install firmware from a local TFTP server via the BIOS, under CLI control. Caution: Installing firmware from a local TFTP
FortiGate Administration Guide - FortiOS 4.0    Product Documentation
FortiGate ™ Version 4.0 Administration Guide Visit http://support.fortinet.com to register your FortiGate product. By registering you can receive product updates, technical support, and FortiGuard services. FortiGate Administration Guide Version 4.0 24 April 2009 01-400-89802-20090424 © Copyright 2009
Configuring Dual Internet Links (Design Considerations)    Knowledge Article
Description There are two separate considerations when using two Internet uplinks: Link Redundancy and Load Sharing. These two features can be combined or implemented separately.
“The system has entered conserve mode” FortiGate log message explanation    Knowledge Article
“The system has entered conserve mode” FortiGate log message explanation DescriptionAn explanation of the log message "The system has entered conserve mode."Components · All FortiGate units · FortiOS Steps or Commands The FortiGate
Troubleshooting Tool : Using the FortiOS built-in packet sniffer    Knowledge Article
Introduction Sniffer Basics · Basic sniffing command · Example 1 : Simple trace · Example 2 : Simple trace Filter Functionality · Example 3 : Trace with filters
< prev | next 5 >